Skutt KilnMaster Addendum Bedienungsanleitung PDF herunterladen

6441 SE Johnson Creek Blvd., Portland, OR 97206 Phone (503) 774-6000 Fax (503) 774-7833

www.skutt.com

TAB TEXT HERE TAB TEXT HERE

ADDENDUM

K I L N M A S T E R M A N U A L

13.1 REV 05/20/05

(continued)

KilnMaster Menu

Addendum

New Look and More

Features

The New 600 Series controller is currently being

installed on all new KilnMaster Kilns. The board looks

almost identical to previous models however if you look

in the top right hand corner of the board you will see

that the F/C button has been replaced by a MENU key.

The MENU button gives the Artist easy access to

a host of new features. Toggling from Fahrenheit to

Celsius is now controlled through the MENU key and

follows the same set of instructions. Here are a some of

the new features to look for:

Preheat

16 Segment Programming

Controlled Cooling in Cone Fire Mode

Pre-heat

The Pre-heat feature allows the artist to “Pre-heat”

the kiln when running a Cone Fire Mode program. It

heats the kiln at a slow rate, 80 •F/hr, to 180 •F and

holds it at that temperature for as long as 99.99 hours (1

to 2 hours is sufﬁcient for most projects). After the pre-

heat is complete the controller automatically begins the Cone Fire Mode program.

Pre-heating your ware helps to ensure that any remaining moisture in the clay is slowly released.

Heating a moist clay body too fast, especially above 200 •F, can cause the water to escape violently in the

form of vapor and crack the piece or, in extreme cases, cause the piece to explode.

Prior to the introduction of the “Pre-heat” feature it was neccessary for the artist to program and run

a Ramp and Hold program ﬁrst and then come back to start a Cone Fire Mode program. Now whenever

you enter a ConeFire Mode program the ﬁrst question it asks you is “How long do you want Pre-heat?

Pre-heat has actually been available for sometime on the KilnMaster Controller. The key difference

on the 600 Series Board is that, due to it’s popularity, we have now made it part of the standard program-

ming sequence when entering any Cone Fire Mode program. Instructions for toggleing this feature off

are on page 22 of your operating manual.

Here is how to use the Pre-heat Feature:

Press CONE FIRE

Enter the amount of time for your pre-heat hold in Hours and Minutes

Continue programming the Cone Fire Mode Program as normal.

Press REVIEW to check the program.

Press START

•

1 2 3

Inhaltsverzeichnis

Seite 1 - Addendum

6441 SE Johnson Creek Blvd., Portland, OR 97206 Phone (503) 774-6000 Fax (503) 774-7833www.skutt.comTAB TEXT HERE TAB TEXT HERETAB TEX

Seite 2 - KILNMASTER MENU ADDENDUM

TAB TEXT HERETAB TEXT HERE TAB TEXT HERE TAB TEXT HERE TAB TEXT HEREADDENDUMK I L N M A S T E R M A N U A L13.1 REV 05/20/05KILNMASTER MENU ADDENDUM

Seite 3

TAB TEXT HERETAB TEXT HERE TAB TEXT HERE TAB TEXT HERE TAB TEXT HEREADDENDUMK I L N M A S T E R M A N U A L13.1 REV 05/20/05KILNMASTER MENU ADDENDUM

Kommentare zu diesen Handbüchern

Keine Kommentare

Skutt KilnMaster Addendum Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Ausrüstung Skutt KilnMaster Addendum herunter. Skutt KilnMaster Addendum User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Ausrüstung Skutt KilnMaster Addendum